Room acoustic assessment
How long your room rings now, why, and what it would take to fix.
Plan my room
- You send
- Room size, photos of every surface and how the room is used
- You receive
- A written reverberation estimate with the surfaces that drive it
- Used for
- The panel layout and quote that follow
- Method
- Sabine and Eyring estimates by frequency band
A room that is hard to talk in usually has one problem: sound keeps bouncing between hard surfaces long after it was made, so every new voice lands on top of the last few. Acousticians describe this with reverberation time, the number of seconds a sound takes to fade by 60 decibels once its source stops. The assessment is where we work out that number for your room, find the surfaces responsible for it and decide how far it needs to come down.
What we look at
Most of what decides how a room sounds can be read from its size and its finishes. We ask for:
- Dimensions. Length, width and ceiling height, including the lowest and highest points of a sloped or stepped ceiling. Volume matters as much as surface: a tall room rings longer than a low one with the same floor.
- Every surface and what it is made of. Floor, ceiling, each wall, windows, glass partitions, tile, brick, exposed concrete. Photos of each wall and of the ceiling tell us more than a paragraph.
- How the room is used. Sixty diners on a Friday, a twelve-person open office, a family room with a television, a meeting room that spends the day on video calls. The use sets the target.
- What is already soft. Upholstered booths, curtains, rugs, acoustic ceiling tile, bookshelves. These count, and leaving them out overstates the problem.
You can gather all of this with our room measurement worksheet and send it with your inquiry.
How the estimate is built
We list every surface with its area and an absorption coefficient for each frequency band, from published data for that material. Multiplying area by coefficient gives absorption in sabins (square feet of perfect absorption). The total, together with the room’s volume, goes into the Sabine equation, which in feet reads:
RT60 = 0.049 × volume ÷ total absorption
For rooms that already have a lot of absorption we also run the Eyring formula, which reads lower than Sabine as the average coefficient rises. We report both, by band, because a room can be fine at 2,000 Hz and still boom at 250 Hz, and the panel construction that fixes one does little for the other.
You can try the same arithmetic on your own numbers in the reverberation time calculator.
Example (fictional). A 60-seat dining room, 40 by 30 ft with an 11 ft ceiling, has a sealed wood floor, painted drywall walls and ceiling and 220 sq ft of storefront glass. With an allowance for tables and chairs it totals about 276 sabins at mid frequencies, which puts its reverberation time near 2.3 seconds. The example room walks through the whole plan for this room.
What you receive
A short written assessment that you can read without an acoustics background. It contains:
- The estimate, now. Reverberation time by frequency band, with the method and the coefficients we assumed, so anyone can check the arithmetic.
- The surfaces that drive it. A ranked list of where the reflections come from. Usually two or three surfaces carry most of the problem: a hard ceiling over the tables, a long glass wall, a tiled floor.
- A target and why we chose it. A decay time that suits the room’s use, with the reasoning, so you can disagree before anything is designed.
- What it would take. How much absorption the room needs to reach the target, expressed in square feet of panel at a stated coefficient. This becomes the starting point for acoustic design.
What an estimate cannot tell you
A calculation is a model, and we say so in every report. It assumes sound spreads fairly evenly through the room, which is less true in long narrow spaces, rooms with all the absorption on one surface, or spaces with big openings into other rooms. It does not measure noise coming in from outside, sound passing through walls or the hum of an HVAC system. If your problem is a neighbor’s voice through a wall rather than echo inside the room, panels are the wrong tool, and we will tell you that rather than sell you panels.
Where a measurement is worth having, reverberation time can be measured on site with an impulse or a test signal, following the methods in ISO 3382-2. We will tell you when we think that is the case and what it involves.
When to start here
Start with an assessment if you are not sure how many panels you need, if you have tried a few panels and heard little difference, or if a designer or landlord wants numbers before approving anything on the walls. If you already know the room and want to talk finishes, send us the room and we will start with the plan.
Send us the room
Room size, a few photos and what happens in the space. We reply with questions or an outline of the plan.