Reverberation time calculator
Estimate how long your room rings from its size and its finishes.
Plan my room
- You enter
- Room size, finish coefficients, glass and furniture
- You get
- Reverberation time by Sabine and by Eyring
- Formula
- RT60 = 0.049 × volume ÷ absorption
- Covers
- One frequency band at a time
Calculator
Reverberation time is the number of seconds a sound takes to fade by 60 decibels after its source stops. It is the single number that best explains why a room feels loud: when a room rings for two seconds or more, every voice is still bouncing around when the next one starts, so people talk louder to be heard. This calculator estimates it from the room’s size and what its surfaces are made of, the same way our room acoustic assessment begins.
How to use it
- Enter the room’s length, width and ceiling height in feet. For a sloped or stepped ceiling, use the average height.
- Enter an absorption coefficient for the floor, the ceiling and the walls. A coefficient is the share of sound a surface absorbs, from 0 (none) to about 1 (nearly all). Use values for the 500 to 1,000 Hz range, the mid frequencies used throughout this site. The hints beside each field give typical ranges.
- Enter the area of windows and glass doors and their coefficient. The calculator takes the glass out of the wall area so it is not counted twice.
- Add furniture and other absorption in sabins: upholstered seating, curtains, rugs, people. Leave it at 0 for an empty room.
Results update as you type.
The formula
A sabin is one square foot of perfect absorption. Each surface contributes its area times its coefficient, and the total absorption, A, goes into the Sabine formula, which in feet reads:
RT60 = 0.049 × volume ÷ A
The calculator also gives the Eyring estimate, which works from the average coefficient across all the room’s surfaces:
RT60 = 0.049 × volume ÷ (surface area × -ln(1 - average coefficient) + furniture sabins)
In a hard room the two agree closely. As the average coefficient rises, Eyring reads lower than Sabine. We report both in a room plan, and so does this calculator.
Reading the result
The results list the room volume, the total surface area, the total absorption, the average coefficient and the two estimates. The average coefficient is a quick check on the room: near 0.05, it is almost entirely hard surfaces.
There is no single right number. No building code sets a reverberation target for restaurants or homes. Rating systems give reference points for some rooms: LEED v4.1 lists under 0.6 seconds for conference and teleconference rooms, and under 0.8 seconds for open-plan offices without sound masking and for hotel meeting or banquet rooms, at 500, 1,000 and 2,000 Hz. Our example room aims for about 1 second, which is a planning choice, not a rule.
Worked example
Example (fictional). The default values describe the example room, a 60-seat dining room that is not a Fibson project: 40 by 30 ft with an 11 ft ceiling, a sealed wood floor at 0.07, painted gypsum board ceiling and walls at 0.05, 220 sq ft of storefront glass at 0.12, and a 40-sabin allowance for tables, chairs and the bar. The results read:
- Room volume: 13,200 cu ft
- Total surface area: 3,940 sq ft (floor 1,200, ceiling 1,200, walls including glass 1,540)
- Total absorption: 276.4 sabins (floor 84.0, ceiling 60.0, walls 66.0, glass 26.4, furniture 40.0)
- Average absorption coefficient: 0.060
- Reverberation time (Sabine): 2.34 s
- Reverberation time (Eyring): 2.28 s
The painted ceiling and walls make up 2,520 sq ft and contribute only 126 sabins. That is where a panel plan starts.
Then change one thing at a time. Enter 0.70 for the ceiling, a value inside the range the hint gives for acoustic ceiling tile, and the Sabine estimate falls to 0.61 s while Eyring falls to 0.53 s. The gap between the two formulas widens once a room has real absorption in it.
What the estimate cannot tell you
- Other frequencies. The defaults are mid-frequency values. A room can be fine at 2,000 Hz and still boom at 250 Hz. To check another band, run it again with coefficients for that band.
- Uneven rooms. Sabine assumes sound spreads evenly. Long narrow rooms, rooms with all their absorption on one surface and rooms open to other spaces behave differently. ASTM C423 says lab coefficients “should be used with caution” because real surfaces are larger than test samples and real rooms rarely have an even sound field.
- A full house. People and clothing absorb sound, so a full room usually rings less than an empty one. The furniture field is where you allow for that.
- Noise from elsewhere. The estimate says nothing about sound coming through walls, HVAC hum or street noise. Panels do not fix those.
Next steps
To turn the result into a panel count, take it to the panel quantity calculator. To list surfaces one by one, such as a brick wall, a tiled bar front or a carpeted corner, use the surface finish worksheet. When you want the estimate done for you, by frequency band and with every coefficient sourced, send the room with Plan my room.
Send us the room
Room size, a few photos and what happens in the space. We reply with questions or an outline of the plan.