Fabric-wrapped wall panels
An absorptive core wrapped in fabric, sized and colored for your walls.
Plan my room
- Core
- Mineral wool, fiberglass or PET, chosen per room
- Face
- Acoustically transparent fabric in your color
- Mounting
- Flat to the wall or over a stated air gap
- Data
- Core and fabric makers' reports named in the proposal
A fabric-wrapped wall panel is the acoustic panel most people picture: a rigid board of porous material wrapped in fabric thin and open enough for sound to pass straight through. Sound that reaches the core loses its energy among the fibers instead of bouncing back into the room. From across the room it reads as a flat, upholstered panel in whatever color the plan calls for.
How it is built
- The core. A rigid board of mineral wool, fiberglass or PET (polyester) fiber. The core does the absorbing, and its thickness and density decide how much it absorbs and how low in pitch it reaches. Thin panels do well on speech and little for bass.
- The fabric. An acoustically transparent fabric stretched over the face and edges and fixed at the back. A tight weave, a backing or a coating would make sound bounce off the fabric before it reaches the core, so we choose fabrics made for the purpose and name their makers in your proposal.
- The edges. Stiffened so the panel keeps its shape and the fabric wraps clean, crisp corners. The edge profile is part of the plan.
- The back. Concealed hardware holds the panel flat to the wall or a set distance off it. An air gap behind a panel improves its absorption at lower frequencies; the air gap calculator shows the frequency at which a given gap starts to help.
Where it works best
- Walls at ear height. In a dining room, a band of panels at seated ear height sits where voices land. In meeting rooms, panels on facing walls keep speech from bouncing back and forth across the table. GSA’s workplace guidance asks for absorptive panels on 25 percent of the walls in conference, meeting and training rooms.
- Parallel walls. Two hard walls facing each other produce flutter, a fast rattling echo after a clap. A few panels on one or both walls usually break it up.
- Rooms where the ceiling is off limits. Landlord rules, a crowded sprinkler layout or a decorative ceiling can leave the walls as the only place for absorption.
Where it does not
- Where people lean, bump and spill. Banquette backs, chair height and the wall behind a bar take wear that fabric shows. Place panels above the contact zone or choose a tougher finish.
- Kitchens and wet areas. Grease and steam load fabric quickly.
- Bass problems. A boomy media room, or a room where low hum is the complaint, needs thicker panels, air gaps or a different approach.
- Noise from next door. Panels absorb sound inside a room. They do not stop sound passing through walls, and they carry no STC rating.
Sizes and options
There is no fixed catalog. We make each panel to the width, height, thickness, edge profile and fabric in your plan, so a run of panels can fill the wall between two windows exactly or stop short of a light switch. Every layout is drawn on an elevation of your wall, with each panel numbered. The wall coverage calculator shows how much of a wall a given grid covers. You see fabric samples before anything is made, and custom fabrication explains the approvals.
How absorption and fire are documented
Fibson has not yet tested its finished panels. For each wall panel, the proposal names its source: absorption data published by the core maker for a named product, thickness and density, tested to ASTM C423 (with the edition) in Type A mounting, laid directly against the test surface, by a named lab, with the report number and date. Type A is the right mounting to cite for a panel fixed flat to a wall; a panel spaced off the wall needs data from a spaced mounting. Installed results vary with room shape, furnishings, occupancy and mounting.
Where we quote a single number, we say which one: NRC, rounded to 0.05, or SAA, rounded to 0.01. We prefer to show the full table by frequency band, because two panels with the same NRC can behave quite differently at 125 Hz, which NRC leaves out.
Fire is documented the same way. ASTM E84 reports a flame spread index and a smoke-developed index, and the IBC groups them into Class A (flame spread 0 to 25), Class B (26 to 75) and Class C (76 to 200), each with a smoke-developed index of 450 or less. A core’s rating does not automatically carry over to a wrapped panel: E84 itself notes that supporting materials can change results. So the proposal gives the class, both indices, the E84 edition and exactly what was tested, and a class applies to your panels only where the report covers the core, fabric and adhesive as built. Then it states the class your room requires.
Installation and code notes
- Protrusion. On a circulation path, objects with a leading edge more than 27 in and not more than 80 in above the floor may protrude no more than 4 in from the wall (ADA 307.2). Most flat-mounted panels sit well within that; spacers and thick cores need checking. The ADA protrusion checker does the arithmetic.
- Interior finish. The IBC treats paneling applied for acoustical correction as interior finish (806.2). The required class depends on occupancy, sprinklers and location, and your local building official has the final say.
- Staying attached. Interior finish must be fastened so it will not readily come off at room temperatures of 200°F for at least 30 minutes (803.14). Our installation support specifies fasteners for your wall type with that requirement in mind.
Care and cleaning
Vacuum the face now and then with a soft brush attachment. Spot-clean following the fabric maker’s instructions, testing on a hidden edge first, and never soak the panel: water carried into the core can stain the face. Do not paint the fabric. Paint closes the weave and turns an absorber into a reflector.
Example (fictional). The example dining room places 14 fabric wall panels, 2 by 4 ft, seven on each long wall at seated ear height: 112 sq ft in all. Using a planning coefficient of 0.80, an assumption rather than a test result, in place of painted gypsum at 0.05, the panels add 112 × 0.75 = 84.0 sabins. On their own they would take the room from 2.34 s to 1.79 s. Together with 16 ceiling clouds and 4 printed art panels, the plan reaches 0.98 s. Mounted, the panels project about 2.5 in, within the 4 in limit. This is not a Fibson project.
Send us the room
Room size, a few photos and what happens in the space. We reply with questions or an outline of the plan.