Fibson homePlan my room
Menu

Why your meeting room echoes on video calls, and how to fix the room

Conference room echo has two causes: a device fault or a reverberant room. How to tell them apart, the 0.6 s target, and where panels help microphones most.

A rose clay felt parrot on a sky blue felt tumbler faces a smaller heather felt parrot across a long olive table, as if the two are repeating each other.
Reader question
Remote participants say our conference room sounds echoey. What in the room causes it, and what treatment fixes it?

Conference room echo on video calls has two different causes. If remote participants hear their own voices coming back to them, sound from the room’s loudspeaker is leaking into its microphone, and the fix is in the audio system: one device joined to the call, echo cancellation working, sensible volume. If remote participants hear your voices as hollow and distant, the microphone is recording the room’s reflections along with your words, and the fix is sound absorption placed where it does the most for the microphone: over the table, on the wall the camera faces, and on one side of each pair of parallel hard surfaces, until mid-frequency reverberation is close to 0.6 seconds.

This guide is for facility managers, IT and AV leads and office designers who keep hearing “you sound like you’re in a bathroom” from the far end. It explains how to tell the two echoes apart in five minutes, why a room that seems fine in person sounds poor on a call, which published targets apply, and where to put absorption, with a worked estimate you can repeat for your own room.

Two kinds of conference room echo, and how to tell which you have

The word “echo” covers two problems with different owners. One is an audio-system fault that the far end hears as their own voice returning. The other is a room problem that the far end hears as your voices smeared by reflections. Diagnose before you buy anything, because panels do nothing for the first, and settings only partly hide the second.

Echo the far end hears: their own voice coming back

Microsoft’s documentation defines acoustic echo cancellation (AEC) as the processing that “removes the echo that occurs when audio played from a device’s loudspeaker is picked up by its microphone”, and notes that without it “the far-end participant hears their own voice played back” (Microsoft Learn). AEC works by comparing the microphone signal with a reference copy of what the device is playing, then subtracting the match.

That last detail explains a common cause in meeting rooms. The echo canceller only knows about audio played by its own device. If someone in the room also joins the call on a laptop with the laptop’s speaker and microphone on, there is now a second loudspeaker and a second microphone that the room system has no reference for. The far end hears its voice return, slightly delayed, from the laptop. The same happens with a phone on speaker, a second room system in a divisible room, or external speakers wired around the processor.

Room echo: your voices arriving with the room attached

The second echo is reverberation. Every voice in the room reaches the microphone once by the direct path and then many more times off the ceiling, the table, the glass and the walls. A loudspeaker-to-microphone fault sounds like a repeat. Reverberation sounds like distance: words lose their edges, quiet talkers at the far end of the table sound as if they are in the next room, and consonants blur into the vowels.

Shure’s guidance on hybrid meetings lists “echo and reverberation from reflective surfaces” among the main reasons remote participants struggle, and says that “glass walls, hard floors, and minimal soft furnishings are aesthetically clean but acoustically hostile” (Shure).

A five-minute test

  1. Ask the far end exactly what they hear: their own voice, or yours sounding hollow.
  2. Mute the room’s microphone for a moment while the far end talks. If the far end’s echo stops, the path is room loudspeaker to room microphone.
  3. Check every laptop and phone in the room. Only one device should carry audio for the room.
  4. With the room empty, clap once in the middle and listen. A smooth fade is reverberation; a fast, buzzing repeat is flutter echo between two parallel hard surfaces.
  5. Have the far end record thirty seconds while three people read the same paragraph from the near end, middle and far end of the table. Play it back in the room.
What the far end reports What is happening Who owns the fix First thing to try
“I hear myself a moment after I speak” Loudspeaker output reaching a microphone without echo cancellation IT or AV One device on audio; check processing settings
“You all sound far away and hollow” Reverberation reaching the microphone with your voices Facilities and design Absorption over the table and on the camera-facing wall
“There is a ringing or buzzing tail” Flutter echo between parallel hard surfaces Facilities and design Absorption on one surface of each parallel pair
“The person at the end of the table fades out” Talker far from the microphone, plus reverberation AV, then facilities Microphone coverage first, then absorption
“I hear the air conditioning” Background noise Facilities Mechanical noise review; absorption will not remove it

If the recording sounds fine but the far end still complains, look first at the device path. If the recording sounds like a stairwell, read on.

Why a room that sounds fine in person sounds hollow on a call

The people in the room hear the same reflections the microphone hears, but they are better at ignoring them. Two ears, head movement and the brain’s ability to focus on one talker all help a listener in the room. A single microphone channel sent to someone wearing earbuds has none of those advantages, so the room’s character arrives at full strength.

Direct sound, early reflections and reverberation

In an article on Shure’s site (now available as an archived copy), Shure engineer Stuart Stephens describes sound in a room as three parts: direct sound, early reflections and reverberation. He explains that reflections arriving within about 50 milliseconds “are almost indistinguishable from the original sound source”, while later reflections form the reverberant field, which “can smear or cloud consonants, making it harder to distinguish between words” (Shure, archived).

The balance between the direct voice and the reverberant field depends on distance. A headset microphone an inch from the mouth hears almost nothing but direct sound. A video bar on top of a screen 10 or 15 feet from the far end of the table hears much more room. This is why the person nearest the camera usually sounds acceptable and the person at the far end sounds distant, even though the room is the same for both.

Flutter echo between parallel surfaces

Stephens also describes flutter echo, which “occurs when two reflective surfaces within a room are parallel (e.g. glass partitions and windows)”, so that sound bounces back and forth and the repeats become audible as a flutter. Meeting rooms are often long boxes with glass on one side and drywall or a whiteboard on the other, which is the classic flutter geometry. Ecophon’s guidance for formal meeting rooms describes the same pattern: “there are often two glass walls and a third that has the obligatory whiteboard”, and speech “will bounce off all these hard surfaces, creating echoes that obscure speech” (Ecophon, archived).

Background noise adds to the problem

Reverberation and background noise compound each other. Shure lists HVAC systems, projector fans and environmental noise among the sounds that “bleed into microphone pickup and compound listener fatigue across longer calls”. Absorption lowers the reverberant build-up of voices in the room, but it does not quiet a noisy diffuser or a humming display. If the far end hears a steady rush, treat that as a mechanical problem first. Owner standards set limits for it: Cornell’s design standard asks for a noise criterion of NC 25 to 30 in office conference rooms, measured with the HVAC and the AV equipment both off and on, where its open-plan offices are allowed NC 40. Cornell’s standard, in other words, expects a meeting room to be quieter than the open floor around it.

What reverberation time to aim for in a meeting room

Aim for a mid-frequency reverberation time of about 0.6 seconds or less in an unoccupied, furnished meeting room. Reverberation time (RT60) is the time sound takes to decay by 60 decibels after the source stops, and it is the one room measure that several US guidelines give a number for.

Source What it says for meeting rooms Notes
WELL v1, Feature 78 Conference rooms: 0.6 seconds maximum RT60 Marked by its publisher as a legacy version
LEED v4.1 BD+C, Table 2 Conference room under 0.6 s; teleconference room under 0.6 s At 500, 1,000 and 2,000 Hz
Cornell 098000 Acoustics, Table 1 Office conference room: RT60 0.5 s, NC 25 to 30, STI 0.75 An owner standard for campus projects, dated January 2019
GSA Sound Matters Ceilings of at least NRC 0.8 in meeting rooms; absorptive panels on 25% of walls, minimum NRC 0.8 A coverage rule, not a time target

Three points help when you use these numbers. First, LEED states its frequencies (500, 1,000 and 2,000 Hz); the WELL and Cornell pages cited do not, so treat their figures as mid-frequency values unless a project says otherwise. Second, they describe the room, not the call: a room that meets 0.6 seconds can still sound poor if the microphone is badly placed. Third, they are voluntary references from two building rating systems, a federal workplace guide and an owner standard, not building code requirements; a project or an owner chooses to adopt them.

The WELL v1 page is marked by its publisher as a legacy version, and the current standard is WELL v2. The sibling article on WELL’s sound requirements and where panels fit covers how v2 treats reverberation, so this guide uses the v1 figure only as a familiar reference point.

How to estimate your room before buying anything

You can estimate reverberation time from the room’s size and finishes with Sabine’s formula, and the estimate is usually close enough to decide how much absorption a meeting room needs. The formula in feet is RT60 = 0.049 × V ÷ A, where V is the room volume in cubic feet and A is the total absorption in sabins (HyperPhysics, Georgia State University). In meters it is 0.161 × V ÷ A.

Step by step

  1. Measure length, width and ceiling height, and multiply for the volume.
  2. List every surface: floor, ceiling, each wall, glass, whiteboards and doors, with their areas.
  3. Give each surface a mid-frequency absorption coefficient from published data for that material. Painted drywall and glass are low (HyperPhysics lists gypsum wallboard at 0.05 and heavy plate glass at 0.04 at 500 Hz); carpet and acoustic ceiling tile are higher.
  4. Multiply area by coefficient for each surface to get sabins, then add an allowance for the table and chairs.
  5. Divide 0.049 × V by the total sabins.
  6. Work out the total absorption your target needs: A = 0.049 × V ÷ target. The difference is what treatment must add.

The reverberation time calculator runs the same arithmetic in your browser.

How far to trust the estimate

ASTM C423, the US laboratory method behind most published absorption coefficients, warns that its coefficients “should be used with caution” because real installations are larger than test specimens and “the sound field is rarely diffuse” (ASTM C423-23). Sabine’s formula assumes sound is spread evenly through the room. In a meeting room where almost all the absorption sits on the ceiling and the walls are bare glass and drywall, sound bouncing horizontally between the walls is treated less than the formula assumes, so flutter can survive a good-looking number. That is one reason the placement rules later in this guide matter as much as the total. The error can also run the other way: HyperPhysics notes that Sabine’s formula “tends to overestimate the reverberation times for enclosures of high absorption coefficient”, so a heavily treated room may measure a little shorter than its estimate.

If you want a measured value instead, ISO 3382-2 “specifies methods for the measurement of reverberation time in ordinary rooms”, including the number of positions and how to report results. ISO’s catalog lists the 2008 edition as reviewed and confirmed in 2022 (ISO, archived catalog page). An acoustical consultant or AV integrator can measure to it; a measured value before and after treatment is the clearest proof the work did what it was meant to.

Where absorption does the most for microphones

Put absorption where it removes the reflections that reach the microphone soonest and strongest. In most meeting rooms that means four places, in this order: the ceiling over the table, the wall the camera faces, one surface of each parallel pair, and the screen wall around the display.

1. The ceiling over the table

A hard ceiling over the table returns each voice straight down toward the table, where tabletop microphones sit and the listeners are seated. The ceiling is also usually the largest surface in the room that is not glass. Acentech principal consultant Ioana Pieleanu, quoted in a 2022 trade article, put it plainly: good speech intelligibility needs low background noise and direct sound that “isn’t overwhelmed by strong reflections off room surfaces”, and “this is why having a sound absorptive ceiling is important in a meeting room” (Propmodo article reprinted by Acentech).

If the ceiling is drywall, a ceiling cloud over the table does the same job without replacing the ceiling, and it absorbs on both faces when hung below it. If the ceiling is already acoustic tile in good condition, check its rating before adding anything; GSA’s figure for meeting rooms is NRC 0.8.

2. The wall the camera faces

The camera on the screen wall faces the wall behind the seats. That back wall receives every voice in the room, since people talk toward the screen, and reflects it straight back toward the microphone on the screen. It is also the backdrop on every call. A panel there does acoustic work and visual work at the same time, which is why a printed or colored panel is a common choice.

3. One surface of each parallel pair

Flutter needs two parallel hard surfaces. Treat one of them and the repeat breaks down. In a room with a glass corridor wall, the parallel partner is the solid wall opposite, so that wall gets panels at seated head height. Ecophon’s formal-meeting guidance asks for “wall absorbers covering at least one wall” in addition to the absorbing ceiling. You rarely need to treat both walls of a pair.

4. The screen wall

The screen wall is the parallel partner of the back wall. Panels on either side of the display finish the job, especially in long rooms where the back wall and screen wall face each other across the table.

The sibling guide to acoustic panel placement in rooms used for talking explains the general rules (ceiling first, spread panels out, one of each parallel pair) for any speech room. The figure below applies them to a typical video room.

Plan of a fictional 20 by 14 ft video room showing where absorption goesA rectangle represents the room. The long bottom wall is glass. Six wall panels sit on the solid long wall at the top. The screen and camera are on the left short wall with a panel on each side. Two printed panels sit on the right short wall that the camera faces. Two ceiling clouds hang over a 12 ft table in the middle. Glass wall to the corridor (no panels) Six 2 x 4 ft wall panels at seated head height (opposite the glass) Screen, camera and side panels Wall the camera faces: two 4 x 6 ft panels Table Two 4 x 8 ft ceiling clouds (dashed) over a 12 x 4 ft table
Fictional example room for illustration, drawn roughly to scale (25 px per foot). The saffron line shows the camera's view toward the back wall. Placement follows the order described in this section; it is not a Fibson project.

Worked example: a glass-fronted video room

The estimate below shows how much each placement contributes in one room, and how close a sensible plan gets to the 0.6 second reference. All coefficients are planning assumptions, not test results, and the room is invented.

Example (fictional). Not a Fibson project. A 10-seat video room, 20 by 14 ft with a 9 ft painted drywall ceiling, a vinyl plank floor, one long wall of glass onto the corridor, and the screen and camera bar on a short wall. Volume 20 × 14 × 9 = 2,520 cu ft. Mid-frequency coefficients are planning assumptions.

Surface Area (sq ft) Coefficient Sabins
Floor, vinyl plank 280 0.03 8.4
Ceiling, painted drywall 280 0.05 14.0
Glass wall 180 0.05 9.0
Other walls, painted drywall (door included) 432 0.05 21.6
Table and chairs (allowance) 15.0
Total 68.0

RT60 = 0.049 × 2,520 ÷ 68.0 = 123.48 ÷ 68.0 = 1.82 seconds.

To reach 0.6 seconds the room needs 123.48 ÷ 0.6 = 205.8 sabins, so treatment must add about 138 sabins.

The plan adds four groups:

  • Two 4 by 8 ft ceiling clouds over the table: 64 sq ft at an assumed 0.90 = 57.6 sabins.
  • Six 2 by 4 ft fabric panels on the solid long wall opposite the glass: 48 sq ft at an assumed 0.80, replacing drywall at 0.05, so a net 0.75 = 36.0 sabins.
  • Two 4 by 6 ft printed panels on the back wall the camera faces: 48 sq ft at net 0.75 = 36.0 sabins.
  • Two 2 by 4 ft panels either side of the screen: 16 sq ft at net 0.75 = 12.0 sabins.

Added: 141.6 sabins. New total 68.0 + 141.6 = 209.6 sabins. RT60 = 123.48 ÷ 209.6 = 0.59 seconds.

Estimated reverberation time as each panel group is addedHorizontal bars. Untreated 1.82 seconds. Ceiling clouds only 0.98 seconds. Clouds plus the wall opposite the glass 0.76 seconds. Adding the camera-facing wall 0.62 seconds. Adding the screen wall 0.59 seconds. A vertical line marks the 0.6 second reference. Untreated Clouds only + wall opposite glass + camera-facing wall + screen wall 1.82 s 0.98 s 0.76 s 0.62 s 0.59 s 0.6 s reference (WELL v1, LEED v4.1) Bar length is proportional to estimated RT60
Fictional example data for illustration: Sabine estimates for the invented 20 by 14 ft room above, using planning-assumption coefficients, not test results. Reference line from WELL v1 Feature 78 and LEED v4.1 BD+C Table 2, checked November 2026.

What the example teaches

  • The ceiling does the most per square foot. The two clouds alone take the room from 1.82 to 0.98 seconds with 64 sq ft of material. All the wall panels together (112 sq ft) without the clouds would reach 84.0 added sabins and 123.48 ÷ 152.0 = 0.81 seconds.
  • Single walls do less than people expect. The six panels opposite the glass on their own give 123.48 ÷ 104.0 = 1.19 seconds. Their job is to break the flutter between glass and drywall, not to carry the whole target.
  • Coverage rules and time targets are different tests. The plan meets 0.59 seconds with panels on 112 of 612 sq ft of wall, about 18%, which is below GSA’s 25% coverage figure. The clouds make up the difference. If a project has adopted GSA’s figure, it needs about 153 sq ft of wall panels regardless of the time estimate.
  • Bare glass stays bare. Nothing goes on the glass, and the plan still works because the opposite wall and the ceiling are treated.

Choosing the target for your room

Use 0.6 seconds as the default for a meeting room that hosts video calls, and consider 0.5 seconds for a boardroom or a room where people often join from the far end of a long table, which is the value Cornell’s standard uses for office conference rooms. The estimate describes an empty, furnished room. People add absorption: the textbook table on HyperPhysics lists upholstered seating at 0.6 at 500 Hz when empty and 0.8 when occupied, so a full room will be a little shorter. Plan for the empty case, because many calls happen with two or three people in a room built for ten.

Glass-walled rooms: treat what is not glass

A glass-walled meeting room is treated through its solid surfaces: the ceiling, the one or two walls that are not glass, and the furnishings. Panels cannot go on the glass, and covering it defeats the reason it was chosen.

When two or three walls are glass

Some rooms have glass on the corridor side and the exterior side, leaving only the screen wall and perhaps one short wall solid. Then the ceiling carries most of the load. A drywall ceiling should become an absorbing ceiling, either by replacing it with high-performing tile or by hanging clouds that cover most of the area over the table and seats. The remaining solid walls get panels, with priority to the one the camera faces. Where glass faces glass, a fabric shade or curtain on the exterior glazing, drawn during calls, gives the flutter path one soft surface; GSA’s guide suggests the same for windows in open workspaces (“curtains or sound-absorbing shades”).

Glass rooms and privacy are a separate problem

Glass fronts also let sound out, and remote callers are not the only people who notice. Panels inside the room shorten the echo; they do not stop voices reaching the corridor. Cornell’s design standard, for example, suggests considering “insulated glazing units (IGUs) in glass walls at conference rooms, glass sidelites and glass doors”, and its tables set sound isolation between rooms separately from reverberation. GSA asks for STC 53 walls to isolate video conference and training rooms. A 2016 article in The Construction Specifier describes how glass-fronted conference rooms leak speech through glass, door gaps and the ceiling, and how electronic sound masking outside the room can cover what escapes (The Construction Specifier). If leakage is part of the complaint, plan for it alongside the echo work, not instead of it.

Huddle rooms: small, close and still boxy

Huddle rooms usually have short reverberation times on paper and still sound boxy on calls. The volume is small, so Sabine’s formula gives a low number quickly, but the microphone sits a few feet from hard surfaces and receives very strong early reflections.

Example (fictional). Not a Fibson project. A four-person huddle room, 10 by 8 ft with a 9 ft drywall ceiling, carpet tile, one 10 ft glass front and an all-in-one video bar under the screen. Volume 720 cu ft. Coefficients are planning assumptions: carpet tile 80 sq ft at 0.25 = 20.0 sabins; ceiling 80 at 0.05 = 4.0; glass 90 at 0.05 = 4.5; drywall walls 234 at 0.05 = 11.7; furniture allowance 5.0. Total 45.2 sabins. RT60 = 0.049 × 720 ÷ 45.2 = 35.28 ÷ 45.2 = 0.78 seconds.

One 4 by 4 ft cloud over the table (16 sq ft at 0.90 = 14.4 sabins) and two 2 by 4 ft panels on the solid wall opposite the glass (16 sq ft at net 0.75 = 12.0 sabins) add 26.4 sabins. New total 71.6; RT60 = 35.28 ÷ 71.6 = 0.49 seconds.

Why the number is not the whole story

In a room this size, a voice reflected off a wall 2 feet behind the video bar travels about 4 feet farther than the direct sound. At roughly 1,125 feet per second, that reflection arrives about 3.6 milliseconds later, well inside the 50 millisecond window Stephens describes as indistinguishable from the original. The microphone hears it as part of the voice, coloring it rather than echoing it. Absorption on the wall right behind or beside the microphone, and on the ceiling directly above it, reduces those first reflections in a way the room total does not show.

Low frequencies matter more in small rooms

Ecophon’s meeting-room guidance asks for a ceiling with “good absorption qualities at low frequencies”, noting low frequencies as a particular concern “especially if video conferencing equipment is installed”. Stephens explains that room modes, a room’s natural resonant frequencies, depend on its dimensions, and in a small room the video bar’s loudspeaker excites them along with every voice. When you compare products for a huddle room, read the full frequency table in the test report rather than the NRC alone. NRC is the average of the absorption coefficients at 250, 500, 1,000 and 2,000 Hz (Intertek’s summary of ASTM C423), so it says nothing about the bands below 250 Hz. The same summary notes that ASTM E795 sets the mounting used in the test, and mounting changes results, so compare the 125 and 250 Hz values for the exact thickness and mounting you would install. The air gap calculator shows which frequency a given mounting depth relates to.

Common fixes that disappoint

Most failed meeting-room fixes share one of five patterns. Each is cheap at the start and expensive when it has to be redone.

  • A few foam squares behind the screen. Suppose twelve 1 by 1 ft tiles with an assumed coefficient of 0.50: that is 6 sabins, against the 138 sabins the example room above needs. Small clusters change how a wall looks far more than how the room sounds.
  • Film or graphics on the glass. Decorative film changes privacy and appearance. It leaves a hard, smooth surface that reflects sound much as the glass did, so the flutter path between glass and drywall is unchanged.
  • A new video bar for a room problem. Better microphones and processing help the far end, and coverage problems need them. They do not shorten the reverberation that the people at the table live with.
  • All the panels on one wall. One long run of panels on the wall opposite the glass breaks one flutter path and leaves the screen wall and back wall reflecting at each other. Spread the same area over the ceiling and two or three walls.
  • Forgetting the whiteboard and the door. A full-height whiteboard wall is as hard as glass. If it faces the glass or another hard wall, it is half of a parallel pair and needs a treated partner.

Finishes that suit a meeting room

Meeting rooms are hard on wall finishes. Chair backs hit panels at seated height, people lean on them, and markers end up near them. Ask for the fabric’s abrasion and cleaning data, keep panels clear of the whiteboard tray, and put the more delicate or decorative finishes where chairs do not reach, such as above a credenza on the back wall. Panels count as interior finish under the building code, so each finish needs a fire classification that covers the assembly as installed; the materials and safety page explains which test reports to ask for, and the local building official decides what applies.

What software can and cannot do

Audio processing can hide a lot of room sound from the far end, and it is worth configuring well. It cannot change what the people in the room hear, and it works best when the room gives it a cleaner signal to start with.

What processing does

Room systems combine echo cancellation, noise reduction and automatic mixing, and some add dereverberation. Shure’s guidance goes as far as saying that “solving this does not always require physical acoustic treatment”, describing processing that removes reverberation in real time, and its FAQ says its dereverberation works “with no physical acoustic treatment required”. Shure also stresses microphone coverage: “a single tabletop device cannot consistently capture every voice”, and its quick guide recommends a ceiling array with steerable pickup for boardrooms.

Where it stops

  • People in the room still hear the room. Dereverberation acts on the outgoing signal. Your colleagues at the table still sit inside 1.8 seconds of reverberation, still raise their voices, and still struggle with flutter.
  • The far end’s voice still rings in your room. The loudspeaker output reverberates too, so remote speakers sound worse to the people in the room.
  • Every processor works on what reaches the microphone. The less reverberant energy arrives with the voice, the less the processing has to remove.
  • Settings drift. A firmware update, a replaced display or a laptop joined with audio on can undo careful tuning; absorption on the ceiling does not change with the software.

The same Shure engineer who described reflections and flutter in the archived boardroom article offered a starting point for treatment: “covering approximately 20% of the surface area of a room is a good starting point for controlling the reverberant field”, with acoustic ceiling tiles to supplement walls where wall space is limited. He also warned that removing reverberation entirely can make a room sound “dead”, which is why the references in this guide are maximums to reach, not a reason to cover every surface.

For a single person on calls from a spare room, the balance is different: the microphone is close and one voice matters. The sibling guide to home office acoustics for clearer calls covers that case.

Fix the room in this order

Work from the cheapest, most likely cause to the most permanent fix, and test after each step so you know which change helped.

  1. Rule out device echo. One device carries audio for the room. Confirm echo cancellation is active in the room system and that loudspeaker volume is reasonable. Ask the far end again.
  2. Record a baseline. Use the five-minute test above and keep the recording. It is your before sample.
  3. Estimate or measure the room. Measure the room and finishes and run the Sabine estimate, or have an integrator measure to ISO 3382-2. Compare with 0.6 seconds.
  4. Check the microphone. Is the farthest seat within the coverage the maker states for the device? If not, expect a microphone change as well as treatment.
  5. Treat the ceiling over the table. Clouds under a drywall ceiling, or higher-performing tile.
  6. Treat the wall the camera faces. It is the backdrop and usually the strongest wall reflection into the microphone.
  7. Break each parallel pair. One surface of glass versus drywall, and the screen wall versus the back wall.
  8. Check depth and clearance. Wall panels along a circulation path must not project more than 4 inches where their leading edges are between 27 and 80 inches above the floor, and anything hung over a circulation path must leave 80 inches of clear headroom (2010 ADA Standards, 307.2 and 307.4).
  9. Retest with the same recording. Same paragraph, same seats, same far-end listener.

Checklist before you order panels

  • Device echo ruled out, with one device on audio.
  • Room dimensions, ceiling type, floor finish and glass areas recorded.
  • Estimated or measured RT60, and the target you chose, written down.
  • Clouds, wall panels and screen-wall panels sized and counted.
  • Test reports for every proposed product, with the test method (ASTM C423), the mounting type and the full frequency table.
  • Fire classification for each finish, confirmed for the assembly as installed.
  • A note on sound leaving the room if privacy is part of the complaint.

The meeting room acoustics checklist turns this into a list you can fill in and keep. Fibson designs and makes acoustic panels to order and plans each room before anything is ordered; its meeting rooms page shows how a plan places panels around the seats, the screen and the camera. If you would like a written estimate for your own room, send its dimensions and a photo of each wall.

Working on a room like this?

Send the size, a few photos and what happens in the space. We reply with questions or an outline of the panel plan.

Plan my room